Moving ahead in 2015

6/9/2015 

Pictures by  Andy Savage show the latest progress on the chassis and and wheelsets


 

---

14/08/2015.    

Ron Walker reports:
Last week I was at Boston Lodge works  helping with the FR Kids Training week. At the same time some of the team that are working on KS-4415 were there.
The chassis has had almost all of the components removed, and during the week it was lifted on to its side for cleaning underneath. With the chassis on its side, one can see where the locomotive was converted to 3 foot gauge. The contractors will soon be sandblasting it ready for  minor repairs and re-painting.
The wheels are out and will be re-profiled soon, the springs have gone away for refurbishment.

A section of the old foundry has been cleared for the components, of which some have already been cleaned, others await cleaning.

---

3/5/2015. 

Pictures and report by by Dave High

The first picture shows the wheel sets, with springs attached to the top of the axleboxes and the turnbuckle chain tensioners. The tensioner between the leading & central axlebox was missing, the flat bar installed to allow the loco to be moved  to Boston Lodge can clearly be seen. The near side far spring is also missing, but the temporary packers for the move can be seen. The tyres have a lot of life in them, and the journals & bearing are in such good condition that they can be re-used without any work. Subject to a detailed measure up the sprockets also appear to be serviceable, and a potential chain supplier has been identified. An immediate priority is to refurbish the springs, including the supply of a replacement. These are palleted up, ready for dispatch, with a copy of the original drawing. Job No 2 is to fettle up the tensioners and manufacture a replacement. Again, the original drawings are available

 


Removing the layshaft. In this picture on the left is the transmission band brake (which isn’t actually on the transmission).   The sprocket for the chain drive to the wheels can then be glimpsed, followed by the spur gear which is the final link from the gear box.

---

2/5/2015 

Picture by Andy Savage shows the dismantled chassis in Boston Lodge

---

11th April 2015

Stripped of the body, it looks just like the General Arrangement drawing reproduced in the 11 January 1929 copy of Engineering. The box with the sloped casing on the right is the gearbox. This drives through spur gears onto the ‘lay shaft’, the red cover of which is located in the frames. The central box on the cross-braced frame is the fuel tank, with the drive shaft between the engine and the gear box located beneath. It has a cone-type clutch located in the red flywheel, on the RHS of the engine.(Dave High)

First steps September 2014

14/9/2014. Dave High reports:

At Boston Lodge, with the massive Mauritian sand boxes and the tatty front cover removed KS4415 looks a lot better. While the bottom of the body is clearly rotten, much of the original material can be recovered.

---

9th September 2014

The diesel engine is now at Boston Lodge,  having been moved there from Minffordd to get it close to workshop facilities.The good news is that after some patient work led by Rob Bishop the engine now runs, and runs well. Consequently morale among the volunteer team is high, and some of that enthusiasm has transferred to the Boston Lodge staff as well.

This year the WHR Superpower Weekend on 12-14th September is based at the Porthmadog end of the WHR and it is hoped to make the engine and loco an exhibit at Boston Lodge.
The first grant application has unfortunately been unsuccessful but submissions to other bodies are planned.

---

Early September 2014

The loco was extracted from the shed at Minffordd and taken to Boston Lodge for display during Superpower 2014:

Planning the restoration

Restoration plans as drawn up in 2014

Assessment 

Renewed activity since 2012 has led to the compilation of  Strategy for Restoration and a Conservation Management Plan
It is reckoned that the original estimate for restoration of £80,000  by Alan Keef &Co could be reduced to £40,000 if the restoration were to be based on volunteer labour.

The following is based on the Conservation Management Plan:

Mechanical Condition

The locomotive was surveyed in December 1999 by Patrick M Keef of Alan Keef Ltd, Railway Engineers,
Lea Line, Ross on Wye, Herefordshire, on behalf of the Greenwich and District Narrow Gauge
Society. The survey showed that the locomotive, with the exception of the engine, is basically repairable
and can be put to rights with a significant investment of time and finance.

Engine

The locomotive is fitted with a McLaren MR4 diesel engine of 1945, equipped with electric
start. This unit is in a derelict condition, with much of the pipework and other ancillary
equipment missing or very badly corroded. At this stage it is felt that this unit is beyond viable restoration.

 Bodywork

The locomotive was provided with a cab which currently consists of two lower sides and a
back plate, with a spectacle plate surviving loose on the locomotive’s footplate.The top section of the cab had to be removed prior to shipment in the container. It was subsequently damaged during
transit and ultimately lost.
In general terms the bodywork is in very poor shape, but is mainly original. During the locomotive’s life the panel-work has suffered from quite severe denting and patching and then severe corrosion during its period as a static display. In addition all ofthe side covers are missing, and an extra section has been cut out of the lower cab sheet to assist with engine cooling in hot climates. The top of the bonnet is missing, along with the large silencer.

 Frames

The frame is a substantial riveted fabrication consisting of deep side frames and buffer beams.
Integral with these are the footplates, and engine and gearbox mounting channels. All
components are riveted together with corner angles. There are signs that the front left-hand
section of the side frame has been removed at some stage, possibly to repair the brake drum,and been
replaced with some rather indifferent riveting. This will require further investigation.
The front buffer beam has been badly bent during prolonged periods of shunting, and has
subsequently been plated and welded. Externally where the frame plates have been painted, all are in
fair condition. On the inside where there has been no recent paint, there is a considerable level of corrosion
caused by the salt atmosphere. The engine and gearbox mounting channels are in similar condition.

Gearbox

The gearbox unit is the key to the overall restoration. During the inspection the main top cover was
unbolted to reveal the internal components. Perhaps surprisingly considering the length of time the
machine has been out of service all is in remarkably good condition, with no sign of water ingress or
condensation, and very clean oil in the sump.

Clutch

The clutch is of the cone type, and is incorporated as part of the flywheel. It is mechanically operated
by a pedal in the cab. The drive is then taken through the clutch shaft to the gearbox via a Hardy-
Spicer flexible coupling. This area of the loco has been exposed to the elements, and has therefore
suffered from a high level of corrosion

Wheels

The wheels and gears are cast steel. The 24” diameter wheels are all flanged, press fitted to the
axles, and run in plain bearing axleboxes. The drive sprockets are bolted on the face of the
wheel centre, with a cork axlebox oil seal running on the vertical face. The tyres are in fair
condition, but with plenty of remaining material to allow for re-profiling. The locomotive is
currently 24” rail gauge with a back to back measurement of 21½” . It is likely that the
locomotive will require re-gauging prior to use on the Festiniog and Welsh Highland Railways. This
operation will necessitate minor modifications of the axlebox oil seal arrangements.

The journals appear to be in sound condition, with a minimal amount of water marking. The
brasses are again in good condition with a good amount of crown thickness and minimal end
wear. The axlebox oil lubrication pads are in very poor condition and will require
replacement. They appear to be of the same type fitted to the 60hp. Simplex locomotives, a standard
off-the-shelf item. The cork oil seals will also require replacement. Four of the axlebox covers are
missing.

The wheelsets are mounted on separate channels designed to facilitate the re-gauging of the
locomotive. These have suffered from considerable corrosion and will require replacement.
The main running springs are in poor condition, and in one case completely missing. There are also
secondary volute springs mounted above the axleboxes, again a number of these are missing.

Fittings

Cab fittings are few. All the major driver’s control levers are all complete, and these comprise:-
direction change, speed change, and band-brake lever, foot operated clutch, and screw
operated handbrake. The throttle control is missing. All the above linkages are seized solid with heavy
corrosion.

Brakes

The locomotive is equipped with a columnar screw hand-brake set against the back plate of
the cab, operating on four wheels. A considerable amount of corrosion has taken place, and the linkage
will require freeing off prior to use; in addition, one brake block is missing.

Finish

The locomotive frames painted black. The buffing beams, some details and axlebox covers are painted
red. The cab and bonnet are painted green. The engine and ancillary equipment is
painted light grey.